Drone manufacturing in a single digital loop
From specification, planning, and procurement to production, quality control, traceability, and export control in Syntech Manufacturing
Key steps
The video follows production in Syntech Manufacturing, using drone and body armor examples from the same factory. Use these stages to follow how specifications, planning, materials, production records, quality, and shipment connect within one system.
1. Establish the product definition and production route
- Start with the product card and specification. Review the reconnaissance drone’s eight-item specification and distinguish current revision A from revision B awaiting approval. The proposed change concerns corrosion-resistant fasteners, so the revision status matters when interpreting the product definition.
- Review the route alongside the specification. Follow the five operations across airframe manufacturing, avionics installation, and testing sections. Identify the three operations with quality control so that the route is understood as both a production sequence and a set of inspection points.
- Check the scheduled shifts and teams. The demonstration shows that these are already assigned before the later production records are reviewed. Read them alongside the route to connect the planned operations with the people and shifts scheduled to perform them.
- Keep planned changes distinct from recorded substitutions. The specification shows a fastener change awaiting approval, while the later product passport records a replacement because standard fasteners were unavailable. Review each record in its own context rather than treating a proposed revision and an actual component replacement as the same event.
2. Connect demand, material planning, and procurement
- Follow the production plan through the MRP calculation. The October plan expands the specification and adds lines for airframe and avionics semi-finished products. Review these resulting requirements to see shortages before they reach the shop floor, as demonstrated in the video.
- Inspect how an order is divided into batches. On the body armor line, an order for 200 units becomes one batch of 40 and two batches of 80. Check the status and material availability of each batch separately, because the first batch is already released with a material shortage.
- Trace the requisition through its approval stages. The avionics request requires approval from both the procurement manager and the finance director because its amount exceeds a threshold. Follow both stages to understand why this request involves two approvers rather than assuming every purchase follows an identical path.
- Compare invoices with the underlying quantities and prices. The demonstration includes nine units invoiced against eight received and an invoiced price of 13,500 against an ordered price of 12,800. Review quantity and price discrepancies separately so the difference in each supplier invoice is explicit.
3. Follow receiving, warehouse storage, and transfers
- Review what happens when a batch is received. In the demonstration, receipt immediately produces a label and an incoming inspection document. Follow these records together to connect the received batch with its identification and incoming quality check.
- Read the warehouse bin structure. The central warehouse has separate bins for motors, propellers, and controllers, shared bins for GPS and telemetry, and a finished-goods bin. Use this layout to understand where the demonstrated materials and finished products are recorded.
- Trace transfers through every warehouse involved. The body armor example moves goods from the central warehouse to a regional warehouse through a transit warehouse. Follow the issue and receipt records rather than looking only at the starting and destination locations, because the demonstration also records an automatically confirmed item mix-up.
- Check the transfer’s final completion status. The illustrated movement is closed as partially completed. Read that status together with the transfer events so that a closed record is not mistaken for confirmation that the entire movement was completed.
4. Record execution, quality, and serial traceability
- Distinguish production order states from actual progress. The video shows planned, released, and completed orders, alongside a blocked order for four Yastrub U1 units at zero percent completion. Review the stated material shortage with the order status to understand why an order can exist without production having progressed.
- Inspect the work order’s execution records. The first Hryf R1 unit has five operations with named performers and actual time recorded for each. Use these records to connect the route with who performed the work and how much time was actually spent.
- Read measured quality results and non-conformity outcomes. The drone work order includes checks for avionics insulation resistance, assembly integrity, GPS accuracy, and telemetry range, all marked as passed. The body armor example also shows non-conformities leading to supplier return, rework, or write-off according to the cause of the defect.
- Follow the product passport and serial number. Review the component list, recorded fastener replacement, route performers, and numerical quality results together under the product’s serial number. Compare the airframe that reached the finished-product stage with the one stopped at avionics integration, and use code scanning to open the product card without searching through lists.
5. Review readiness, acceptance, shipment, and delivery dates
- Check equipment and personnel readiness. The body armor line shows overdue maintenance, overdue instrument verification, and a qualification matrix identifying approaching expirations. Review these records alongside production activity to see the equipment and qualification issues presented in the demonstration.
- Follow the compliance and acceptance records before reviewing shipment. The Hryf R1 is linked to an export license, and its end user has passed screening with an “Allowed” status. The video then shows an accepted military acceptance report and shipment from the warehouse, connecting the product with its compliance and acceptance records.
- Keep outstanding demand visible after other products ship. The Yastrub U1 line remains in shortage because the product has not been built, while requests from units continue feeding the order queue. Review the recalculated promised dates: the demonstrated shortage pushes readiness back by 38 days, making the delay explicit rather than hiding it behind another product’s completed shipment.
- Use the dashboards to review the wider production picture. The body armor line’s Andon board shows downtime events, and its dashboards show average equipment effectiveness above 80% across sections. Read these overview figures alongside individual orders and operational records, keeping the displayed body armor results distinct from the drone examples.
Transcript
One SYNTECH-Miltech factory produces body armor and combat drones, and the entire production cycle is controlled by a single system: Syntech Manufacturing.
The product card for the Gryphon R-1 reconnaissance drone. A specification with eight items, current revision A, and revision B awaiting approval, with a note about replacing the fasteners with corrosion-resistant ones.
The route for the Gryphon R-1. Five operations across the new airframe manufacturing, avionics installation, and testing sections, with quality control at three operations. Shifts and teams have already been scheduled.
The production plan for October expands the specification through an actual MRP calculation and adds lines for airframe and avionics semi-finished products before the shortage reaches the shop floor.
On the body armor line, the same order for 200 units is split into three batches: 40 and two batches of 80. The first has already been released to production with an actual material shortage.
The avionics requisition goes through two-stage approval: the procurement manager and the finance director, because the amount exceeded the threshold. And receiving the batch immediately prints a label and an incoming inspection document.
On the central warehouse racks, there are separate bins for motors, propellers, and controllers, shared bins for GPS and telemetry, and one finished-goods bin.
Another example from the body armor line. An organized transfer from the central warehouse to the regional warehouse through a transit warehouse: issue, receipt, and an automatically confirmed item mix-up. The transfer is closed as partially completed.
Production orders in different states: planned, released, completed. And a genuinely blocked order for four Yastrub U1 units. Zero percent complete, because the warhead has never been purchased.
A work order for the first Hryf R1 unit. Five operations with named performers and actual time worked on each.
[Music]
Four measured checks on this work order: avionics insulation resistance, assembly integrity, GPS accuracy, and telemetry range. All are marked as passed.
And on the body armor line, non-conformity registration works in the same way. Return to the supplier, rework, or write-off, depending on the cause of the defect.
The Hryf R1 product passport under a single serial number. Its component list includes a line marked “replaced” for the fasteners, its route includes performers, and its quality records include numerical results; the replacement itself was registered automatically because no standard fasteners remained.
The same airframe passes through the stages under one number. One body reached the finished-product stage through assembly and avionics installation. The second was deliberately stopped halfway through, at the avionics integration stage.
[Music]
Scanning the code immediately opens the product card without searching through lists.
On the body armor line, equipment and people are also under control. Overdue maintenance and instrument verification are immediately visible, and the qualification matrix shows whose qualifications are nearing expiry.
Two supplier invoices with discrepancies. In quantity: nine invoiced versus eight received; and in price: 13,500 versus the ordered price of 12,800.
[Music]
The Hryf R1 is linked to an export license, and the end user, military unit A 7040, has passed screening and received an “Allowed” status.
The military acceptance report for the first Hryf R1 unit has been accepted by the military unit’s representative, and the product has been shipped from the warehouse. The Yastrub U1 line remains in shortage, honestly, because the product has not yet been built.
Requests from units for drones feed the order queue. An actual recalculation of promised dates shows that the Yastrub U1 will be ready 38 days later, specifically because of the warhead shortage.
And the overall picture is visible on the body armor line dashboards. An Andon board with downtime events and an average equipment effectiveness figure above 80% across the sections.
[Music]
Syntech Manufacturing. One system for body armor and unmanned systems. From specification to signed shipment. Request a demonstration today.
What does drone manufacturing look like when the entire process is in one system?
From product catalog and specification to production, quality control, equipment, and export control.
In the video, we show how Syntech Manufacturing helps manage the production cycle:
— product catalog and specifications;
— route, sections, shifts
— demand, plan
— breaking down orders into batches
— procurement, approval, acceptance
— warehouse, cells, balances
— quality control and non-conformities;
— serial numbers and traceability;
.....
As a result, data about the product, materials, production operations, quality, and equipment are not scattered between Excel, chats, and separate systems — they are connected in a single digital loop.
Syntech Manufacturing — from specification to finished product.
Learn more about Syntech Manufacturing
Related: Manufacturing (MES/MRP)
Comments & questions
Sign in or register to leave a comment or question.
Sign in / Register