How to control goods in transit between warehouses
Transit warehouse in Syntech Manufacturing: from dispatch to actual receipt with control of partial deliveries
Key steps
In Syntech Manufacturing, a transfer can be tracked through a transit warehouse between dispatch and receipt. The video follows a request for 15 units when only 12 are available, showing why confirmation, actual issue, goods in transit, and actual receipt must be treated as distinct stages.
1. Establish the requested quantity and available stock
- Start with the quantity requested for the transfer: in the video, the storeroom requests 15 units. Keep that requested quantity in view throughout the process, because it is the reference for comparing what is actually issued and received. A request describes the intended movement, not goods that have already changed warehouses.
- Check the stock available at the dispatch warehouse against the request. In the example, only 12 units are available, so the warehouse cannot issue all 15 requested units from that available stock. Recognizing this difference before dispatch helps distinguish the original requirement from the quantity that can actually move in this transfer.
- Distinguish a confirmed transfer and reserved goods from an actual warehouse issue. The video explicitly shows that the transfer is confirmed and the goods are reserved while nothing has moved yet. Do not interpret this stage as completed dispatch: goods leave the sending warehouse only when the sender issues them.
2. Record the actual issue from the dispatch warehouse
- At the dispatch warehouse, create the issue order for the goods being sent. This is the document used in the video to record the actual outgoing quantity, rather than treating the transfer request itself as proof of movement. Keep the distinction clear between requesting goods and issuing them from the warehouse.
- Post the quantity that is actually available and issued: 12 out of the requested 15 units in this example. Do not substitute the requested quantity for the actual issue quantity. Recording the real issue preserves the difference between what the storeroom asked for and what the dispatch warehouse could supply.
- Review the resulting shortfall of three units and keep it separate from the 12 units that have been issued. The video shows that this shortage is immediately visible and that the transfer remains open at this point. A partial dispatch therefore does not make the outstanding portion of the original request disappear.
3. Follow the goods through the transit warehouse
- Use the in-transit report to see what is currently held in the transit warehouse. This covers the interval after goods have left the dispatch warehouse but before the destination warehouse has accepted them. The purpose is to identify the goods between those two events, rather than assume that dispatch also means receipt.
- Review since when the goods have been in transit and the transfer under which they are recorded. These are the details described in the video for understanding the intermediate stage. They connect the goods currently in transit with their transfer and show the period when they are no longer with the sender but not yet with the recipient.
- Keep the issued quantity distinct from the unfulfilled part of the request when interpreting the transfer. In the example, 12 units are issued, while three units are a shortfall against the requested 15. The transit stage concerns goods that have actually left the sending warehouse, not the three units that were unavailable for issue.
4. Confirm actual receipt at the destination warehouse
- At the receiving warehouse, create a receipt order and accept the goods. Receipt is a separate action from dispatch, just as actual issue is separate from confirming the transfer. Use this stage to record the goods arriving at the destination rather than considering them received merely because the sender has issued them.
- Confirm the actual quantity received; in the demonstrated transfer, the receiving warehouse accepts the 12 units that were issued. Compare that receipt with the actual dispatch as well as the original request. This keeps the completed movement of 12 units clear without suggesting that the full request for 15 units has been fulfilled.
- After receipt, review the stock at the destination and the corresponding transit position. The video shows that the stock immediately appears at the destination warehouse and the transit warehouse is cleared. For the demonstrated goods, this marks the end of the intermediate stage between leaving the sender and being accepted by the recipient.
5. Review partial completion and receiving discrepancies
- Read the final outcome as partially completed, not as full fulfillment of the request. The video describes the transfer as closing with this outcome after the goods are received. Its quantities remain explicit: 15 units requested, 12 issued, and 12 received, so completion of that movement does not mean all requested units were supplied.
- Keep the remaining three units visible as the outstanding part of the original requirement. The video states that these units remain open until next time, even though the transfer is closed as partially completed. Distinguish this outstanding requirement from goods in transit: the 12 issued units have already been received and the transit warehouse has been cleared.
- If the wrong goods or the wrong quantity arrive, use the discrepancy recorded by the system during receipt. The video states that the system records this discrepancy itself and the storekeeper confirms it with one click. This addresses a mismatch at receiving, separately from the example's known shortage of three units at the dispatch warehouse.
Transcript
A transfer on paper is not yet the movement of goods. Goods leave a warehouse only when the sender issues them, and arrive only when the recipient accepts them.
The storeroom requests a transfer of 15 units. Only 12 are available at the dispatch warehouse. The transfer is confirmed, and the goods are reserved, but they have not moved anywhere yet.
The dispatch warehouse creates an issue order and posts exactly what is actually available. 12 out of 15. The shortfall is three units. This is immediately visible, and the transfer remains open.
The in-transit report shows exactly what is currently held in the transit warehouse. Since when, and under which transfer, the goods no longer belong to the sender and do not yet belong to the recipient.
The receiving warehouse creates a receipt order and accepts the goods. The stock immediately appears at the destination warehouse, and the transit warehouse is cleared.
The transfer is closed as partially completed. 15 requested, 12 issued and received, with three units remaining open until next time.
And if the wrong goods or the wrong quantity arrive for receipt, the system records the discrepancy itself, and the storekeeper confirms it with one click.
Every step of the transfer between warehouses is under control. From request to shelf. Request a demonstration of Syntech Manufacturing on our website.
Goods have left one warehouse but have not yet arrived at another. How to control where they are?
In Syntech Manufacturing, transfers can be tracked through a transit warehouse.
In the video, we show the process step-by-step:
— the dispatch warehouse generates the transfer;
— the goods leave the warehouse;
— the system records them as being in transit;
— the destination warehouse confirms actual receipt.
If the delivery is partial, you can record the actual quantity and continue to control the remaining balance in transit.
This way, production receives a clear status of materials at each stage — from dispatch to receipt.
Learn more about Syntech Manufacturing
Comments & questions
Sign in or register to leave a comment or question.
Sign in / Register